I am surprised that automatic bedding sifters are not mentioned in this article. The primary reason for stall cleaning is to create a healthy environment for the horse. Poorly maintained dirty stalls are home to numerous pathogens that cause infection and disease. Wet bedding is a primary cause of thrush, a hoof disease. Ammonia gas from urine causes respiratory problems by forming ammonium hydroxide, a caustic base, in the lungs and bronchial tubes when it comes in contact with moisture on the tissues that line them. Daily removal of urine-saturated bedding is necessary to maintain peak respiratory function.It is easier to prevent fly breeding than to control adult flies. Eliminating the habitat required by the larvae to hatch and grow significantly reduces fly populations. Stalls that are dusty can cause allergy and respiratory problems. Rubber mats provide a measure of padding and insulation and are impermeable to urine, which is absorbed by the bedding. The wet spot must be removed daily. The manual method has been the common method of stall cleaning for many years and if done well by an experienced worker produces an acceptably clean looking stall but up to 25% of manure bits are left in the bedding. Hand picking is tedious and time consuming. Average time to clean a stall is 15 to 20 minutes if done well. The manual method takes its toll on the body and can cause tennis elbow, carpal tunnel syndrome and chronic back pain. Hand picking is arbitrary and in order to save time or avoid pain, the cleaner often throws good bedding away with waste. Time can be saved at the expense of bedding or bedding can be saved at the expense of time. Neither case makes good business sense in the long run. Additionally, the waste stream can be doubled by the inclusion of bedding that could have been recycled using the automatic method, discussed below. Automatic Sifting is The best way to clean a horse stall. Automatic sifting is an efficient and economical stall cleaning method with an almost perfect end result. All manure larger than a kernel of corn is removed in less than half the time for manual picking. The Brockwood Stall Shi*fter is the first and most reliable automatic manure and bedding sifter on the market today. It can be seen at http://www.brockwoodfarm.com.
I'm one of the lucky ones who has an uber neat horse. She does both eliminations in a back corner and does not walk through it at all. It still takes me about twenty minutes to clean her stall, which includes walking out and getting fresh shavings, carting them back and arranging them. I choose thorough over quick any day. It takes me more than ten minutes because I *care* about my horse and I don't want to miss anything. I'm not an employee at a huge barn who has to do twenty stalls a day...I do one stall, my horse's stall, and I do it well, even if I do say so myself. :) I liked the article, but think that it's a bit unrealistic for those of us who work to clean our stalls more than once a day. Unless your job is at the barn, then maybe that makes sense. :)
I really enjoyed understanding step by step how stall cleaning is done at the Kentucky horse park, however as a barn owner of a mid sized stable in Oregon, I would go broke if I had to pay my workers for that kind of tedious job. Our horses are turned out all day and we use shavings or pelleted sawdust bedding. A commenter mentions using a automatic sifting unit as a a better alternative and this is definitely a great idea. There are issues with using auto sifting units however, such as: they are big and cumbersome, require a plug in are going to be too large to use effectively in the average 12x12 stall, etc. This is where one would think a hand tool to be much more useful! For those of you who have not seen it - the Berto Shake'n Fork is the answer! It is a power sifting manure fork, that requires no cords, is light weight and does the job quick easy and fast. Plus the tines on the fork are nearly indestructible! It has been a great addition to our barn and we have both the motorized Shake'n Fork and the manual model, the Flex'n Fork. For any barn I recommend using it and your workers will be happy with it too. You can see it at http://www.shakenfork.com Hope this helps for those who are still looking for a solution to their stall cleaning issues. :)
The Shake'n Fork is a neat little device but not built for the same level of stall cleaning that the Brockwood Stall Shi*fter is suited for. The Shaken fork will do the same job that any other fine tine fork will do but do it faster. It will not clean a stall as thoroughly as the Brockwood Stall Shi*fter. The Stall Shi*fter will thoroughly clean a 12 x 12 stall bedded about 3 inches deep in 5 to 6 minutes and will remove every particle larger than a kernel of corn; the Shake’n Fork , as good as it is, won’t do that. A Shake’n Fork is an excellent tool if you just want to quickly pick the obvious piles but a Stall Shi*fter completely aerates all the bedding passing through the screen. There are hundreds satisfied Shi*fter users who would disagree with Joy about the big and cumbersome part. A Stall Shi*fter will not only remove every piece of manure larger than a kernel of field corn it will reduce bedding usage by average of 50 percent and time to completely clean, refresh and re-spread the stall by 60%. The palms down labor of shaking a manure fork aggravates tennis elbow the palms up labor of simply scooping the manure and bedding with a shovel and putting it on the shaking screen does not. If you are like Xena from Dawson Creek, BC and are interested in doing a thorough job for the least amount of labor and bedding usage and have tennis elbow you will appreciate the Brockwood Stall Shi*fter. It is in a class by itself.
Is there any equipment that be purchased to ease the back burden of cleaning the stalls other than a bobcat?
My horses think I am their personal maid, I will have to read this article to them and I bet they will laugh. But it sounds like cleaning will be fun. I wonder if this will also work for house work!!!
Good article, but I do things a bit differently. I get the scooper and wheelbarrow ready and start at the back of the stall, scooping up all manure piles and bits I find for about a 1 foot strip. Then I scrape everything away from the wall so there is a 2-foot strip of mat showing through. If wet spots anywhere in the stall, I remove completely before moving the area. Then I work my way toward the stall front until about 1 foot away. I follow the same steps as the back end, then check to make sure everything is clean. Once all dirty shavings and waste is removed, I push all shavings up against the sides to allow wet spots on the mat to dry. I go on to finish all the other stalls like that, then go back and spread out remaining shavings and add more as needed to each stall. I get fully done with 8 12x12 stalls in about 1hr30min, including up to 4 trips out to manure pile to dump the wheelbarrow, with this habit.